Reference Manual
00809-0100-4530, Rev BA
July 2009
Rosemount 5300 Series
www.rosemount.com
Section 7 Service and Troubleshooting
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-1
Analyzing the Measurement Signal . . . . . . . . . . . . . . . . . page 7-3
Surface Pulse Not Found . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-5
Disturbance Echo Handling . . . . . . . . . . . . . . . . . . . . . . . . page 7-7
Interface Pulse not Found . . . . . . . . . . . . . . . . . . . . . . . . . page 7-8
Using the Echo Curve Analyzer . . . . . . . . . . . . . . . . . . . . page 7-10
Interface Measurements with Fully Submerged Probes . page 7-15
Analog Output Calibration . . . . . . . . . . . . . . . . . . . . . . . . . page 7-16
Level and Distance Calibration . . . . . . . . . . . . . . . . . . . . . page 7-17
Logging Measurement Data . . . . . . . . . . . . . . . . . . . . . . . . page 7-19
Backing up the Transmitter Configuration . . . . . . . . . . . . page 7-20
Configuration Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-21
Reset to Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . page 7-22
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-23
Using the Simulation Mode . . . . . . . . . . . . . . . . . . . . . . . . page 7-25
Write Protecting a Transmitter . . . . . . . . . . . . . . . . . . . . . page 7-26
Enter Service Mode in RRM . . . . . . . . . . . . . . . . . . . . . . . . page 7-26
Viewing Input and Holding Registers . . . . . . . . . . . . . . . . page 7-27
Removing the Transmitter Head . . . . . . . . . . . . . . . . . . . . page 7-28
Changing a Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-29
Diagnostic Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-33
LCD Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-42
LED Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7-43
Foundation Fieldbus Error Messages . . . . . . . . . . . . . . . page 7-44
SAFETY MESSAGES Procedures and instructions in this section may require special precautions to
ensure the safety of the personnel performing the operations. Information that
raises potential safety issues is indicated by a warning symbol ( ). Please
refer to the following safety messages before performing an operation
preceded by this symbol.
(126 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels